GA. to INDY

[jrj5x5]

Tomorrow I am off to secure a trailer for move from GA. to INDY. On the 27th.
My wish is to see the machine run in the am on the 27th and then load it up in the late am or early pm. spend the night locally and then head home on the 28th.
I believe that the machine weights around 1700lbs. I think i am going to get a open trailer and tarp the hell outa the thing.

Keep Cutting
Jim J.

[Joey Jarrard]

We are working over time to get this done.
Joey

[jrj5x5]

We are working over time to get this done.
Joey
Tell everyone I said thanks for the hard work on my machine.

Got the trailer reserved today, I choose one with a ramp, deck size 6x12, 2100 lb weight limit.

Joey: Got any recommendations on a local hotel?

Did mach3 install ok on the box I sent?

[jrj5x5]

Tell everyone I said thanks for the hard work on my machine.

Got the trailer reserved today, I choose one with a ramp, deck size 6x12, 2100 lb weight limit.

Joey: Got any recommendations on a local hotel?

Did mach3 install ok on the box I sent?

I am leaving Friday to Huntsville AL. And I will head out around 9am monday from Huntsville to Camaster to pick up my new machine.
I am extreamly excited, so this will be a very long week.
My wife and I got time off from work, hotels set, trailer on reserve,
just did a check up on the van, so I'm all set to go.

[james mcgrew]

paul is driving home from camaster tonight and is a happy camper with his machine he has photos for us and has reported to me that your machine will be ready for pick up!! he took a lot of photos and had high praises for all at the plant including the new fellow "paul" we should have pics tommorrow

i did not feel well enough to drive over today its 10 hours roundtrip in one day for me so maybe monday!!

jim

[Joey Jarrard]

would love to have you on monday. Im not sure but we might have two going out on the same day (monday) I have alot of pics and will post in the am i need to find my cable. Paul S. seamed to like his new CAMaster It is a great machine its one of those you hate to see leave the shop. I will talk to ya in the morn.

James J.
look forward to monday. we are working hard sorry about the lack of post but we are swamped. we are working on mach3 if it does not go well you will be upgraded to WINCNC. none the less it will be going monday. we might have a lose end to tie down it always happens that way. but you'll learn alot and have a chance to drive your machine. Its a great looking 408

Paul S.
Hope you made it home

Joey

[Eric Mims]

Joey, I think you guys left your jack in my shop.. it's a red one. Next time someone's up this way you guys can swing by and grab it.

[james mcgrew]

james yours is third one on right!! ztruck and all is on now!!jim

[Joey Jarrard]

Thanks, I will let you know when I do.

joey

[KeithG]

Hi Oh Great Cut One !
I am experiencing a Z problem and was hoping you could help me out. I am cutting 3/4" birch plywood that is .741" actual thickness. My final pass is at
.7663. This does not exceed my maximum depth allowed into the spoilboard setting in cabinet pro. The two sheets I cut late yesterday afternoon did not cut all the way through until I edited the z depth to .80. I put on a new spoilboard that I milled on both sides to make sure that wasn't the problem. Today, I cut the first two sheets and they cut great. The next five wouldn't cut all the way through. Things that make you go HMMM! Could really use some help on this one :confused:
Thanks!
Keith

[Joey Jarrard]

Does you cnc have a air calender mounted on it to help the Z motor with the weight?