Announcement

Collapse
No announcement yet.

Slow motion in 3D

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Slow motion in 3D

    I recently upgraded to Vetric Aspire and am learning how to make 3D Wavy flags. I can make the drawing and have made a couple of nice looking flags (look ok for the 1st try) But right now I am running a program that has gone into a snails pace. I am using a Stinger 1 with a 3.5 Hp Milwaukee router. For the roughing passes I am using a 1/4 single flute endmill set to run at .25 depth, .1 stepover and a feed rate of 250 ipm. For the finish pass I am using a 1/8 inch ball nose, set at a 300 ipm with a 10% step over. For the stars and the military emblems I am using a 60 degree 7/16 V bit. the time for this bit is not a problem as it's only taking a few minutes. The flags are 12 X 24 inches
    The problem I have is the roughing bit is making 8 passes and taking 5 hours to rough it. The finish pass is taking the same. The Stinger is using Wincnc and I am overriding the feed to double, but the machine is not moving any faster.
    Any suggestions?
    Attached Files
    Stinger 1 SR-23
    Windows 10
    Vectric VCarve Pro
    3.5 Milwaukee router
    Prepped for recoil

  • #id
    which way are you running the cutter

    Comment


    • #id
      In 3D Raster mode, which takes it end to end in Y
      Stinger 1 SR-23
      Windows 10
      Vectric VCarve Pro
      3.5 Milwaukee router
      Prepped for recoil

      Comment


      • #id
        X, y and z are all set at 250 I assume.
        Charlie L
        Stinger II, 48 by 48, 1.7 kW Spindle, FTC + Laser + Recoil + Vacuum, July 2012
        WinCNC 2.5.03, Aspire, PhotoVCarve, Windows 7 Pro SP1

        Comment


        • #id
          Yes they are.
          Stinger 1 SR-23
          Windows 10
          Vectric VCarve Pro
          3.5 Milwaukee router
          Prepped for recoil

          Comment


          • #id
            Looking at your pictures I wonder if the rough work could be done without 3d cuts. Using some vectors in the low sections essentially making pockets that are not full depth. Or, any combination of 2d vectors. Then cut the 3d finish as you are now.

            just thinking.
            Charlie L
            Stinger II, 48 by 48, 1.7 kW Spindle, FTC + Laser + Recoil + Vacuum, July 2012
            WinCNC 2.5.03, Aspire, PhotoVCarve, Windows 7 Pro SP1

            Comment


            • #id
              Is your rapid Z gap set to high in your tool setup I use 0.100
              Harold Phillips
              Custom Gunsmith Specialist ( Remington Arms )
              Stinger 1 SR 24
              1.7 Kw HSD Spindle
              Fast Tool Change (FTC)
              Performance package Pro
              Laser Cross Hair
              48" Stinger Indexing Lathe
              Spindle Speed Control From WINCNC
              KRS Keypad
              Counter Balance
              USB Adapter
              T-Slot System... 2" Gantry Lift
              Aspire 9.5,Vcarve Pro 6.5
              Photo Vcarve, Cut 3D
              hbutch8@aol.com

              Comment


              • #id
                That reminds me. I always set the z clearance at a minimum. Like 0.1 inch so there is less time raising and lowering.
                Charlie L
                Stinger II, 48 by 48, 1.7 kW Spindle, FTC + Laser + Recoil + Vacuum, July 2012
                WinCNC 2.5.03, Aspire, PhotoVCarve, Windows 7 Pro SP1

                Comment


                • #id
                  The retract is not the problem. it's like the machine is going at a super slow motion going along in Y. I finished the flag I was working on and ran a different program to see if there was something wrong with the machine, but it is running fine with another project.
                  Stinger 1 SR-23
                  Windows 10
                  Vectric VCarve Pro
                  3.5 Milwaukee router
                  Prepped for recoil

                  Comment

                  Working...
                  X