CAMheads CNC Router Forum By: CAMaster CNC

Go Back   CAMheads CNC Router Forum By: CAMaster CNC > Members List

JohnnyCNC JohnnyCNC is offline

Camaster Owner

Visitor Messages

Showing Visitor Messages 1 to 10 of 10
  1. krossdal
    10-09-2017 05:48 PM
    Thanks Johnny. I'll take a look at that. I'm running WinCNC 3.0.08.
    I've been busy for the last couple of days and thus I've not been able to reply on the forum.
    I recently got my machine configured so it now uses metric values. F60 and S6 are a feed values in IPM if I'm not mistaken - if so I should probably use 152 and 15.
    These are the first lines of my wincnc.ini: (should a place the lim_buf right after maxstepv line? There is no lim_buf line in my wincnc.ini)

    1. unit=MM
    2. timertype=7200
    3. steppulse=p5
    4. maxstepv=100000
    5. lim_buf=f152s15
  2. JohnnyCNC
    02-06-2015 11:05 AM
    Sorry I didn't see your question Dan,

    Yes, WinCNC uses OptiScout for just the purpose you asked about. It uses a camera to find the registration marks and your cutting tools to cut them out. WinCNC can control routers (as you know), tangential knives, oscillating knives (oscillating saws), and lasers to do the cutting.

    Good question!!
  3. Dan
    08-08-2014 12:57 PM
    Johnny, I have a friend that is setting up to cut a plastic material with an image laminated on it. They have registration marks from the printing software on the top surface. Does wincnc have any module that has software recognition to sync up with registration marks for accurate cut-out?
  4. JohnnyCNC
    11-06-2013 08:04 PM
    No one would recognize me if I changed my name that much after all these years!!

    I'm enjoying your participation Gary. You're keeping me straight on my answers. Don't let up.
  5. Gary Campbell
    11-06-2013 07:21 PM
    Gary Campbell
    Shouldn't that username be JohnnyCNC++ ?
  6. mels'
    04-17-2013 05:09 PM
    just outside of westover about 3 miles. I have a laguna swift 4 x 4.
  7. Rick Vereen
    01-14-2013 07:58 PM
    Rick Vereen
    Having a problem with my Stinger I. Computer died on me yesterday, screen went blank and computer went off. I was able to get it going again though. Now all comes up but the WINCNC controller will not initialize. I have had this once before. Left it for a day and tried it again and came back up and initialized. Is there some type of reset?
  8. Rick Weingart
    08-01-2012 07:50 PM
    Rick Weingart
    Whats up Mr CNC I was wondering if there is a way to nest in a triangle like racking a pool game so to speak . circles in a triangle 9 to be exact 2.5 diameter . I would love the help ! Thanks Rick
  9. copperhead4321
    01-27-2012 07:54 AM
    Hi johnny, I've been cutting with no problems with your revised wincnc you helped me with. I do mostly 3d relief carvings but was wondering if I could have a 2nd wincnc just for 2d which would cut faster than the 50 in/min. that I now have for 3d. i would like to be able to switch/change back and forth according to what I'm cutting(3d or 2d) is this possible for you to do for me? or for me to change the feeds myself?
  10. Rick Vereen
    12-11-2011 08:37 PM
    Rick Vereen
    Don't know if it got through to you but I emailed you.

About Me

  • Signature


Total Posts
Visitor Messages
General Information
  • Last Activity: 12-30-2020 04:15 PM
  • Join Date: 03-19-2009
  • Referrals: 0


Showing Friends 1 to 10 of 12

Contact Info

Instant Messaging
Send an Instant Message to JohnnyCNC Using...
This Page

All times are GMT -4. The time now is 11:22 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.